Good quality charging capacitor - New developed Hybrid Supercapacitor Battery – CRE

Short Description:

Product Detail

Product Tags

Feedback (2)

Our company since its inception, always regards product quality as enterprise life, continuously improve production technology, improve product quality and continuously strengthen enterprise total quality management, in strict accordance with the national standard ISO 9001:2000 for Compact Design Film Capacitor , Film Capacitor For High Power Automotive Application , Snubber Capacitor For Igbt , We, with great passion and faithfulness, are willing to provide you with perfect services and striding forward with you to create a bright future.

Good quality charging capacitor - New developed Hybrid Supercapacitor Battery – CRE Detail:

Application

1. Memory backup

2. Energy storage, mainly used for driving motors require a short time operation,

3. Power, higher power demand for a long time operation,

4. Instantaneous power, for applications that requires relatively high current units or peak currents ranging up to several hundreds of amperes even with a short operating time

Electrical performance and safety performance

No	Item	Test method	Test requirement	Remark
1	Standard charging mode	At room temperature, the product is charged at a constant current of 1C. When the product voltage reaches the charging limit voltage of 16V, the product is charged at constant voltage until the charging current is less than 250mA.	/	/
2	Standard discharge mode	At room temperature, the discharge will be stopped when the product voltage reaches the discharge limit voltage of 9V.	/	/
3	Rated capacitance	1. The product is charged according to the standard charging method.	The product capacity shall be no less than 60000F	/
		2. Stay 10min
		3. The product discharges according to the standard discharge mode.
4	Internal resistance	Ac internal resistance tester tests, precision: 0.01 m Ω	≦5mΩ	/
5	Discharge of high temperature	1. The product is charged according to the standard charging method.	Discharge capacity should ≥ 95% rated capacity, product appearance without deformation, no burst.	/
		2. Put the product into the incubator of 60±2℃ for 2H.
		3. Discharge the product according to the standard discharge mode, recording discharge capacity.
		4. After the discharge, the product will be taken out under normal temperature for 2 hours, and then visual appearance.

6	Low-temperature discharge	1. The product is charged according to the standard charging method.	discharge capacity≧70% no change on rated capacity, cap appearance, no burst	/
		2. Put the product into the incubator of -30±2℃ for 2H.
		3. Discharge the product according to the standard discharge, recording discharge capacity.
		4. After the discharge, the product will be taken out under normal temperature for 2 hours, and then visual appearance.

7	Cycle life	1. The product is charged according to the standard charging method.	No less than 20,000 cycles	/
		2. Stay 10min.
		3. The product discharges according to the standard discharge mode.
		4. Charge and discharge according to the above charging and discharging method for 20,000 cycles, until the discharge capacity is less than 80% of the initial capacity, the cycle is stopped.

Outline drawing

Circuit schematic diagram

sp3

Attention

1. The charging current shall not exceed the maximum charging current of this specification. Charging with a current value higher than the recommended value may cause problems in charging and discharging performance, mechanical performance, safety performance, etc. of the capacitor, resulting in heating or leakage.
2. The charging voltage shall not be higher than the rated voltage of 16V specified in this specification.
The charging voltage is higher than the rated voltage value, which may cause problems in the charging and discharging performance, mechanical performance and safety performance of the capacitor, resulting in heat or leakage.
3. The product must be charged at -30~60℃.
4. If the positive and negative poles of the module are connected correctly, reverse charging is strictly prohibited.
5. The discharge current shall not exceed the maximum discharge current specified in the specification.
6. The product must be discharged at -30~60℃.
7. Product voltage is lower than 9V, please do not force discharge;Full charge before use.

Product detail pictures:

Related Product Guide:

We have been ready to share our knowledge of advertising worldwide and recommend you suitable products at most aggressive costs. So Profi Tools present you ideal price of money and we've been ready to create with each other with Good quality charging capacitor - New developed Hybrid Supercapacitor Battery – CRE , The product will supply to all over the world, such as: Tajikistan, Zimbabwe, America, We believe in quality and customer satisfaction achieved by a team of highly dedicated individuals. The team of our company with the use of cutting-edge technologies delivers impeccable quality products supremely adored and appreciated by our customers worldwide.

Capacitor Supplier

Capacitors Manufacturers In China

Cre Inspection

damping capacitor

Induction Heating For Wind Energy

locomotive capacitor

Metal Film Capacitor

power supply capacitor

welding machine capacitor

X-ray capacitor

The factory technical staff gave us a lot of good advice in the cooperation process, this is very good, we are very grateful.

By Debby from South Africa - 2017.06.29 18:55

The company account manager has a wealth of industry knowledge and experience, he could provide appropriate program according our needs and speak English fluently.

By Madeline from Azerbaijan - 2018.06.26 19:27