Chinese Professional smart grid capacitor - Battery-ultracapacitor hybrid energy storage unit – CRE

Short Description:

Product Detail

Product Tags

Feedback (2)

Our well-equipped facilities and superb good quality control throughout all stages of manufacturing enables us to guarantee total buyer gratification for Dc Link Capacitor In Rail Traction , High Performance Film Capacitor , Self-Healing Dry Capacitor , For even more data, please do not be reluctant to call us. All inquiries from you may be highly appreciated.

Chinese Professional smart grid capacitor - Battery-ultracapacitor hybrid energy storage unit – CRE Detail:

Application

1. Memory backup

2. Energy storage, mainly used for driving motors require a short time operation,

3. Power, higher power demand for a long time operation,

4. Instantaneous power, for applications that requires relatively high current units or peak currents ranging up to several hundreds of amperes even with a short operating time

Electrical performance and safety performance

No	Item	Test method	Test requirement	Remark
1	Standard charging mode	At room temperature, the product is charged at a constant current of 1C. When the product voltage reaches the charging limit voltage of 16V, the product is charged at constant voltage until the charging current is less than 250mA.	/	/
2	Standard discharge mode	At room temperature, the discharge will be stopped when the product voltage reaches the discharge limit voltage of 9V.	/	/
3	Rated capacitance	1. The product is charged according to the standard charging method.	The product capacity shall be no less than 60000F	/
		2. Stay 10min
		3. The product discharges according to the standard discharge mode.
4	Internal resistance	Ac internal resistance tester tests, precision: 0.01 m Ω	≦5mΩ	/
5	Discharge of high temperature	1. The product is charged according to the standard charging method.	Discharge capacity should ≥ 95% rated capacity, product appearance without deformation, no burst.	/
		2. Put the product into the incubator of 60±2℃ for 2H.
		3. Discharge the product according to the standard discharge mode, recording discharge capacity.
		4. After the discharge, the product will be taken out under normal temperature for 2 hours, and then visual appearance.

6	Low-temperature discharge	1. The product is charged according to the standard charging method.	discharge capacity≧70% no change on rated capacity, cap appearance, no burst	/
		2. Put the product into the incubator of -30±2℃ for 2H.
		3. Discharge the product according to the standard discharge, recording discharge capacity.
		4. After the discharge, the product will be taken out under normal temperature for 2 hours, and then visual appearance.

7	Cycle life	1. The product is charged according to the standard charging method.	No less than 20,000 cycles	/
		2. Stay 10min.
		3. The product discharges according to the standard discharge mode.
		4. Charge and discharge according to the above charging and discharging method for 20,000 cycles, until the discharge capacity is less than 80% of the initial capacity, the cycle is stopped.

Outline drawing

Circuit schematic diagram

sp3

Attention

1. The charging current shall not exceed the maximum charging current of this specification. Charging with a current value higher than the recommended value may cause problems in charging and discharging performance, mechanical performance, safety performance, etc. of the capacitor, resulting in heating or leakage.
2. The charging voltage shall not be higher than the rated voltage of 16V specified in this specification.
The charging voltage is higher than the rated voltage value, which may cause problems in the charging and discharging performance, mechanical performance and safety performance of the capacitor, resulting in heat or leakage.
3. The product must be charged at -30~60℃.
4. If the positive and negative poles of the module are connected correctly, reverse charging is strictly prohibited.
5. The discharge current shall not exceed the maximum discharge current specified in the specification.
6. The product must be discharged at -30~60℃.
7. Product voltage is lower than 9V, please do not force discharge;Full charge before use.

Product detail pictures:

Related Product Guide:

carry on to boost, to guarantee products excellent in line with market and consumer standard specifications. Our enterprise has a quality assurance system are actually established for Chinese Professional smart grid capacitor - Battery-ultracapacitor hybrid energy storage unit – CRE , The product will supply to all over the world, such as: Argentina, Suriname, Algeria, Really should any of these items be of interest to you, please let us know. We will be pleased to give you a quotation upon receipt of one's detailed specifications. We've our personal specialist R&D enginners to meet any of the requriements, We look forward to receiving your enquires soon and hope to have the chance to work together with you inside the future. Welcome to take a look at our organization.

absorbing capacitor

automobile capacitor

Chinese capacitor manufacturer

film capacitor in parallel connection

HVDC capacitor

pulse capacitors

rail traction capacitor

vehicle mounted capacitor

wind capacitor

X-ray capacitor

The company can keep up with the changes in this industry market, product updates fast and the price is cheap, this is our second cooperation, it's good.

By Helen from Cambodia - 2017.09.29 11:19

Managers are visionary, they have the idea of "mutual benefits, continuous improvement and innovation", we have a pleasant conversation and Cooperation.

By olivier musset from Sacramento - 2017.11.01 17:04