OEM/ODM China Capacitor Film Manufacturers - New developed Hybrid Supercapacitor Battery – CRE

Short Description:

Product Detail

Product Tags

Feedback (2)

Adhering into the principle of "quality, provider, performance and growth", we now have gained trusts and praises from domestic and intercontinental consumer for Medium Frequency Furnace Resonant Capacitor , Customized Capacitor For Solar Inverter , Dry Type Film Capacitor Solution , If you have the requirement for any of our products, please contact us now. We are looking forward to hearing from you soon.

OEM/ODM China Capacitor Film Manufacturers - New developed Hybrid Supercapacitor Battery – CRE Detail:

Application

1. Memory backup

2. Energy storage, mainly used for driving motors require a short time operation,

3. Power, higher power demand for a long time operation,

4. Instantaneous power, for applications that requires relatively high current units or peak currents ranging up to several hundreds of amperes even with a short operating time

Electrical performance and safety performance

No	Item	Test method	Test requirement	Remark
1	Standard charging mode	At room temperature, the product is charged at a constant current of 1C. When the product voltage reaches the charging limit voltage of 16V, the product is charged at constant voltage until the charging current is less than 250mA.	/	/
2	Standard discharge mode	At room temperature, the discharge will be stopped when the product voltage reaches the discharge limit voltage of 9V.	/	/
3	Rated capacitance	1. The product is charged according to the standard charging method.	The product capacity shall be no less than 60000F	/
		2. Stay 10min
		3. The product discharges according to the standard discharge mode.
4	Internal resistance	Ac internal resistance tester tests, precision: 0.01 m Ω	≦5mΩ	/
5	Discharge of high temperature	1. The product is charged according to the standard charging method.	Discharge capacity should ≥ 95% rated capacity, product appearance without deformation, no burst.	/
		2. Put the product into the incubator of 60±2℃ for 2H.
		3. Discharge the product according to the standard discharge mode, recording discharge capacity.
		4. After the discharge, the product will be taken out under normal temperature for 2 hours, and then visual appearance.

6	Low-temperature discharge	1. The product is charged according to the standard charging method.	discharge capacity≧70% no change on rated capacity, cap appearance, no burst	/
		2. Put the product into the incubator of -30±2℃ for 2H.
		3. Discharge the product according to the standard discharge, recording discharge capacity.
		4. After the discharge, the product will be taken out under normal temperature for 2 hours, and then visual appearance.

7	Cycle life	1. The product is charged according to the standard charging method.	No less than 20,000 cycles	/
		2. Stay 10min.
		3. The product discharges according to the standard discharge mode.
		4. Charge and discharge according to the above charging and discharging method for 20,000 cycles, until the discharge capacity is less than 80% of the initial capacity, the cycle is stopped.

Outline drawing

Circuit schematic diagram

sp3

Attention

1. The charging current shall not exceed the maximum charging current of this specification. Charging with a current value higher than the recommended value may cause problems in charging and discharging performance, mechanical performance, safety performance, etc. of the capacitor, resulting in heating or leakage.
2. The charging voltage shall not be higher than the rated voltage of 16V specified in this specification.
The charging voltage is higher than the rated voltage value, which may cause problems in the charging and discharging performance, mechanical performance and safety performance of the capacitor, resulting in heat or leakage.
3. The product must be charged at -30~60℃.
4. If the positive and negative poles of the module are connected correctly, reverse charging is strictly prohibited.
5. The discharge current shall not exceed the maximum discharge current specified in the specification.
6. The product must be discharged at -30~60℃.
7. Product voltage is lower than 9V, please do not force discharge;Full charge before use.

Product detail pictures:

Related Product Guide:

We normally follow the basic principle "Quality Initial, Prestige Supreme". We've been fully committed to offering our consumers with competitively priced good quality merchandise, prompt delivery and professional support for OEM/ODM China Capacitor Film Manufacturers - New developed Hybrid Supercapacitor Battery – CRE , The product will supply to all over the world, such as: Pakistan, Cambodia, Cyprus, Our expert engineering team will generally be prepared to serve you for consultation and feedback. We are able to also offer you with free of charge samples to meet your requirements. Best efforts will likely be produced to provide you the best service and merchandise. When you are keen on our business and products, please speak to us by sending us emails or call us quickly. In an effort to know our products and company extra, you may come to our factory to view it. We will generally welcome guests from all over the world to our business to create business relations with us. Please feel cost-free to speak to us for small business and we believe we'll share the best trading experience with all our merchants.

Electric Car Capacitor

Good Quality Super Capacitor

Igbt Snubber Capacitor

IGBT/GTO Snubber Capacitor

Induction Heater Capacitor

Metalized Filter

Mkp Capacitor Manufacturer

Pulse Power Capacitors

Snubber Capacitor

X-ray capacitor

This manufacturer can keep improving and perfecting products and service, it is in line with the rules of market competition, a competitive company.

By Natividad from Morocco - 2018.06.18 19:26

The company account manager has a wealth of industry knowledge and experience, he could provide appropriate program according our needs and speak English fluently.

By Rosemary from Melbourne - 2017.05.21 12:31